Tips for How to Build a Deck

A veteran pro tells you his favorite deck building tips that speed up the job, increase deck durability and improve quality. The result is a better deck, less hassle and fewer problems.

Tip 1: Build better stairs

Simple notched stair jacks are fine for interior stairs. They get nailed to wall studs for stability and are hidden once the house is finished. Not so with deck stairs. Naked, notched treated-wood stair jacks are unattractive and wobbly, and because there isn’t much meat to attach posts or pickets to, you’ll have wobbly handrails, too. But it’s easy to strengthen them and spruce them up. Adding sturdy, solid 2×12 skirts to the outside jacks and stair risers does it all.
FH10MAY_DECTIP_02

Tip 2: Seam a deck

 The traditional way most builders go about decking is to randomly stagger joints. The result is that end-to-end deck boards share the 1-1/2-in. thickness of each joist. That can cause problems, especially with wood decks. With only 3/4 in. of nailing surface, fasteners will cause ends to split, and since the board ends have to be tight, untreated wood will rot.

I use a faster, more material-efficient method I call seaming. It’s simply strategically placing a seam (or seams, on bigger decks) and using the same length boards for each section. Each seam is a sandwich made of an elevated vertical decking board with joists on both sides. The advantages are many. It’s faster than random seaming; all decking ends have a full 1-1/2 in. of framing, so it cuts down on fastener splits; and you can leave 1/4-in. gaps at the ends so end grain can dry out after it gets wet.

 The vertical deck board is for looks only. It makes everything look planned and polished. And there’s virtually no waste. If I need to build a 20-ft.-wide deck, I’ll make it about 19 ft. 6 in. and use all 10-ft. decking on both halves. That allows for 1-in. overhangs and cutting off some bad ends.

Seaming also works well for solid composite decking, which comes in fewer lengths. If, for example, I’m building a composite deck, 12- and 20-ft. lengths might be the only options. For a 16-ft.-wide deck, I might seam it to have a 4-ft. “sidewalk” down the middle for zero waste. Of course, everything depends on the design and the homeowner. But think about it next time to figure out the best approach.
FH10MAY_DECTIP_04

Tip 3: Cobble together a layout frame

Home improvement books and TV shows always recommend laying out deck footings with batter boards and string. But I gave that up years ago. It’s faster and easier to build a layout frame from deck boards or joists. And unlike string, a frame gives you a solid guide to mark footing holes and align post bases. You can mark the location of the frame by driving a few stakes and then remove it to dig holes or pour footings. Then you can quickly replace the frame to align post bases or set posts. You can even screw posts to the frame to hold them in perfect position while you backfill.

FH10MAY_DECTIP_05

Tip 4: Leave a little step below doors

There are so many reasons not to snug decks right under door thresholds. The screen and sliding door tracks on patio doors get full of debris. Storm doors have to bulldoze their way through leaves in the fall. And those leaves will get blown or kicked into the house every time the door opens. Splashing water rots out wood casing and jamb trim. And last but not least, water will inevitably work its way under any threshold and rot out the subfloor and then the framing. It’s nearly impossible to flash between ledgers and thresholds if the decking is flush to thresholds. Leave a 3-in. step: The house and its owner will be a lot happier in the long run.

FH10MAY_DECTIP_07

Tip 5: Check the end grain on 4x4s.

When buying 4x4s, don’t just sight them for straightness; always look at the ends. Try to avoid 4x4s that include the center of the tree, especially anywhere near the center of the 4×4. Those can twist into airplane propellers in no time. This is particularly true of 8-footers because those are often the leftovers from “peeling logs,” the outer layers of which have been shaved off to make plywood veneer. When I order 4x4s over the phone and need eights, I always order tens to reduce the chances of getting 4×4 leftovers from peelers.

FH10MAY_DECTIP_06

Tip 6: Get over lag screws

There are few reasons to use lag screws anymore. Construction screws may look wimpy, but they’re actually stronger than lags. And you don’t have to spend five minutes cranking each one in with a ratchet.

Give construction screws a try on your next deck. You can drive them with any 18-volt screw gun without predrilling—they don’t split wood. The price may shock you (they cost four times as much), but you’ll never go back to lags.

FH10MAY_DECTIP_08

Tip 7: Avoid miters

Avoid miters when you can, especially in wide boards. Here’s why. Wood installed outdoors immediately starts shrinking—or in some conditions, expanding—mostly in width. Miters will always open up unevenly, and your perfect miter will look like a hack job in no time. Whenever possible, use simple butt joints. They don’t look as professional as miters at first, but they look better in the long run.

FH10MAY_DECTIP_09

Advertisements

3 thoughts on “Tips for How to Build a Deck

  1. I like your advice to leave the deck three inches below the door. I’m constantly having to clean the floor by my door because a lot of materials are kicked into the house. I am going to remember to do that when I build a deck.

    Liked by 1 person

  2. I have been wanting to build a deck like this, but I wasn’t sure how the design would work in my particular yard. Your visuals were actually really helpful to me, this gives me a much better idea of what kind of landscape is needed for a design like this. However, I don’t think that I will have the time to build this on my own. Do you have any information on how I can contact a qualified professional for a job like this? Thank you for such an applicable article! http://www.rossmonsterdesign.com

    Liked by 1 person

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s